ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

kaidoy021 · 29 March 2008, 04:07 AM

I had just gotten my new DJ and I decided to mess around with the adjustment and remove a link. After testing out the fitment, I decided to add back the link. I was using a cheap precision screwdriver that was a tad thinner than the pin screw slot. It's not really noticeable, but I can see somewhat of some torque marks left on the tiny pin screws head.

Being anal that I am, can I order some new pin screws from the AD? or would I have to order a whole new link to get the new pin screw?

I've also ordered a proper screwdriver (1.6mm screwdriver someone recommended on this board that is for a Panerai) and some Loctite 220 to secure the pin screw.

Thanks,
Patrick

entropydave · 29 March 2008, 04:47 AM

Id like to know too!

Warren · 29 March 2008, 04:59 AM

I got my screw from a local shop http://www.nam-hing.com/. Of cause the price is different from it's web site.
you may try to find similar shop in your area.

Warren · 29 March 2008, 05:01 AM

For your information. As advised by the shop guy, I bought a 1.4mm for my EXP II

Warren · 29 March 2008, 05:28 AM

I think the most critical to avoid torque marks is that you have to hold the steel blade firmly by a blade stand when you screwing the pin.

JPP · 29 March 2008, 05:55 AM

I would like to know too - I took my SD to the RSC in London to get the bracelet adjusted - had a link taken out and then they put it back in and both screws on the two links are damaged and there are scratches all down the side of the clasp where the microadjustment holes are. I am really really peeved about it and am not sure if I am being anal or not. My advice is - don't adjust your watch more than is strictly necessary.

The exact same thing happened with my Ex II.

Not sure why I didn't lear my lesson then...

SPACE-DWELLER · 29 March 2008, 07:54 AM

Just go to your nearest AD and get some screws and have the watch maker make the job for you.

jasonbellevue · 1 April 2008, 03:15 PM

Quote:

Originally Posted by SPACE-DWELLER

Just go to your nearest AD and get some screws and have the watch maker make the job for you.

Good advice.

kaidoy021 · 1 April 2008, 03:13 PM

Went to my local AD and she ordered me pins. They cost $15 each. Thanks again for the advice.

29 March 2008, 04:07 AM	#1
kaidoy021 "TRF" Member Join Date: Mar 2008 Real Name: Patrick Location: San Francisco Watch: DJ 112600ss Posts: 13	Ordering New Pin Screws? I had just gotten my new DJ and I decided to mess around with the adjustment and remove a link. After testing out the fitment, I decided to add back the link. I was using a cheap precision screwdriver that was a tad thinner than the pin screw slot. It's not really noticeable, but I can see somewhat of some torque marks left on the tiny pin screws head. Being anal that I am, can I order some new pin screws from the AD? or would I have to order a whole new link to get the new pin screw? I've also ordered a proper screwdriver (1.6mm screwdriver someone recommended on this board that is for a Panerai) and some Loctite 220 to secure the pin screw. Thanks, Patrick

29 March 2008, 07:54 AM	#7
SPACE-DWELLER "TRF" Member Join Date: Apr 2007 Real Name: Bo Location: Denmark Watch: Rolex, of course! Posts: 22,436	Just go to your nearest AD and get some screws and have the watch maker make the job for you. __________________ With kind regards, Bo LocTite 221: The Taming Of The Screw...

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

29 March 2008, 04:47 AM	#2
entropydave "TRF" Member Join Date: Nov 2007 Real Name: Dave Location: Huntington, IN Posts: 680	Id like to know too!

29 March 2008, 04:59 AM	#3
Warren Member Join Date: Mar 2008 Real Name: Warren Location: Hong Kong Watch: GMT IIc Posts: 132	I got my screw from a local shop http://www.nam-hing.com/. Of cause the price is different from it's web site. you may try to find similar shop in your area.

29 March 2008, 05:01 AM	#4
Warren Member Join Date: Mar 2008 Real Name: Warren Location: Hong Kong Watch: GMT IIc Posts: 132	For your information. As advised by the shop guy, I bought a 1.4mm for my EXP II

29 March 2008, 05:28 AM	#5
Warren Member Join Date: Mar 2008 Real Name: Warren Location: Hong Kong Watch: GMT IIc Posts: 132	I think the most critical to avoid torque marks is that you have to hold the steel blade firmly by a blade stand when you screwing the pin.

29 March 2008, 05:55 AM	#6
JPP Member Join Date: Aug 2007 Location: London Posts: 115	I would like to know too - I took my SD to the RSC in London to get the bracelet adjusted - had a link taken out and then they put it back in and both screws on the two links are damaged and there are scratches all down the side of the clasp where the microadjustment holes are. I am really really peeved about it and am not sure if I am being anal or not. My advice is - don't adjust your watch more than is strictly necessary. The exact same thing happened with my Ex II. Not sure why I didn't lear my lesson then...

1 April 2008, 03:13 PM	#9
kaidoy021 "TRF" Member Join Date: Mar 2008 Real Name: Patrick Location: San Francisco Watch: DJ 112600ss Posts: 13	Went to my local AD and she ordered me pins. They cost $15 each. Thanks again for the advice.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)