The Rolex Forums   The Rolex Watch

ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

Old 5 May 2009, 08:19 AM   #1
gerard88t
"TRF" Member
 
Join Date: Nov 2008
Location: Ask
Posts: 409
Tritium hands

Hi,

Is it advisable to put a bonder on the lume of NOS trit hands before installing on the watch? I feel it is, but would like others take on the subject.

Thanks!
Gerard
gerard88t is offline   Reply With Quote
Old 5 May 2009, 08:28 AM   #2
redshirt1957
"TRF" Member
 
redshirt1957's Avatar
 
Join Date: Sep 2007
Real Name: Bubba
Location: Bitsyville!
Watch: Blue YM today!
Posts: 10,053
Quote:
Originally Posted by gerard88t View Post
Hi,

Is it advisable to put a bonder on the lume of NOS trit hands before installing on the watch? I feel it is, but would like others take on the subject.

Thanks!
Gerard
Bob Ridley has applied some sort of bonder to the tritium hands on my watches, when needed, during service. I cannot tell the difference and, of couse, I trust Bob 100%.
redshirt1957 is offline   Reply With Quote
Old 5 May 2009, 08:29 AM   #3
abr68
Banned
 
Join Date: Dec 2007
Real Name: Axel
Location: Germany
Watch: view my signature
Posts: 612
Hi Gerard,
To be honest I donīt get your question
Best
Axel
abr68 is offline   Reply With Quote
Old 5 May 2009, 08:55 AM   #4
gerard88t
"TRF" Member
 
Join Date: Nov 2008
Location: Ask
Posts: 409
Thanks.

And Axel I will be installing a set of the trit hands I got today on my 16800 at service time (bummer is I see it was serviced in 2007 so it will be getting an unneeded service). Since trit is so fragile I want the back side where lume is, bonded with a clear coat bonder. That way it ensures 0 flaking and other bad stuff that can happen to tritium over time inside a watch.
gerard88t is offline   Reply With Quote
Old 5 May 2009, 09:10 AM   #5
abr68
Banned
 
Join Date: Dec 2007
Real Name: Axel
Location: Germany
Watch: view my signature
Posts: 612
Quote:
Originally Posted by gerard88t View Post
Thanks.

And Axel I will be installing a set of the trit hands I got today on my 16800 at service time (bummer is I see it was serviced in 2007 so it will be getting an unneeded service). Since trit is so fragile I want the back side where lume is, bonded with a clear coat bonder. That way it ensures 0 flaking and other bad stuff that can happen to tritium over time inside a watch.

Gerard,
For sure it is up to you whatever you want to do but as written in my response to your question there is and should be NO NEED to get a NOS hand set touched in any way....
It destroys some authenticity and also value is going that way.
Just leave it as it is and maybe go that way in some decades when there is a need for...
abr68 is offline   Reply With Quote
Old 5 May 2009, 09:51 AM   #6
Balboa
Member
 
Join Date: Apr 2009
Location: SoCal OC U.S.A.
Posts: 342
This seems like a very sensible idea to me. It will not effect the look or function in any way but should eliminate or at least slow down the flaking of the material. A cosmetic issue mostly, but it will also keep loose material from finding its way into the movement.

What it will not do, of course, is extend or preserve the luminosity. Watch hands of the same age whether they are installed on a watch worn every day or hands that have been stored in a sealed package, have lost their luminosity at the same rate.

This is one of the limitations of using tritium which has a relatively short half life of about twelve years. Watches that use tritium are now getting old enough that the luminosity is pretty much gone. There is no fix for this. One of the newer synthetics could be applied to the hands and markers to restore useful luminosity, but in many cases loss of value and authenticity will preclude using such a fix.

Mark
Balboa is offline   Reply With Quote
Old 5 May 2009, 10:20 AM   #7
Tools
TRF Moderator & 2024 SubLV41 Patron
 
Tools's Avatar
 
Join Date: May 2007
Real Name: Larry
Location: Mojave Desert
Watch: GMT's
Posts: 43,515
Quote:
Originally Posted by gerard88t View Post
Hi,

Is it advisable to put a bonder on the lume of NOS trit hands before installing on the watch? I feel it is, but would like others take on the subject.

Thanks!
Gerard
I think that bonding is a good idea if you feel that there is some degradation of the Trit. It will stabilize it and keep it from flaking or deteriorating further..

Bonding or stabilizing pigments is a time honored way of preservation of masters paintings and any other aged pigment (which the tritium is) and preserves the value rather than allowing it to continue in decline..

However, your question is about applying it to NOS parts, which should not be exhibiting any problems... I do not see it as a way of stopping anything because the original bonding agents in the NOS pigments is still sound, so adding a sound compound to an already sound pigment accomplishes little.
__________________
(Chill ... It's just a watch Forum.....)
NAWCC Member
Tools is offline   Reply With Quote
Old 5 May 2009, 12:46 PM   #8
gerard88t
"TRF" Member
 
Join Date: Nov 2008
Location: Ask
Posts: 409
Thanks everyone! Great, helpful answers. Now it's up to me. I guess I will leave them as they are.
gerard88t is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

OCWatches

Wrist Aficionado

My Watch LLC

WatchesOff5th

DavidSW Watches

Takuya Watches


*Banners Of The Month*
This space is provided to horological resources.





Copyright Đ2004-2024, The Rolex Forums. All Rights Reserved.

ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

Rolex is a registered trademark of ROLEX USA. The Rolex Forums is not affiliated with ROLEX USA in any way.