The Rolex Forums   The Rolex Watch

ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX


Go Back   Rolex Forums - Rolex Forum > Other (non-Rolex) Watch Topics > Audemars Piguet Discussion Forum

Reply
 
Thread Tools Display Modes
Old 7 November 2020, 07:51 PM   #1
kctt
"TRF" Member
 
kctt's Avatar
 
Join Date: Dec 2010
Location: Melbourne
Watch: AP Diver/SD/GMTIIc
Posts: 228
Interesting quirk on my AP Diver

I've had the watch from new for 10 years now and found an interesting quirk that I never knew. These days, the watch is hardly worn and sits in the watch drawer.

Two days ago, I decided to set the time to the 10:10 position. At this time, the watch does not have any power reserve left. I don't remember the position of the hour and minute hands, just that I set it to 10:10. When I screwed the crown back on, I noticed the watch was ticking. I didn't move the watch that much to have caused the rotor to wind the watch. Hmmm... maybe the mainspring hasn't fully unwound I thought. Strange.

The next morning, the watch stopped running but the time showed 4 o'clock! Means the watch was actually ticking for 6 hours! I then set it to 10:10 again but this time was careful not to move the watch at all. Again, the watch was ticking after I screwed the crown. This morning, I found the watch showing around the half past 4 mark again! I repeated the exercise and this time watch stopped just before 5 o'clock. Seems like the watch runs for around 6 hours each time.

Before you guys say anything, I didn't wind the watch, it was on the set time position. What do you think happened here? I'm keen to hear if anyone came across this before.
__________________
Rolex Sea Dweller 16600, Rolex GMT Master II 116710LN, Audemars Piguet Royal Oak Offshore Diver, Omega Seamaster Professional, Tudor Pelagos 25600TB, Tudor Black Bay Dark, Zenith Defy Classic

IG: @idighorology
kctt is offline   Reply With Quote
Old 7 November 2020, 08:08 PM   #2
mnl
"TRF" Member
 
Join Date: May 2018
Location: sf
Watch: 15450ST
Posts: 541
Quote:
Originally Posted by kctt View Post
I've had the watch from new for 10 years now and found an interesting quirk that I never knew. These days, the watch is hardly worn and sits in the watch drawer.

Two days ago, I decided to set the time to the 10:10 position. At this time, the watch does not have any power reserve left. I don't remember the position of the hour and minute hands, just that I set it to 10:10. When I screwed the crown back on, I noticed the watch was ticking. I didn't move the watch that much to have caused the rotor to wind the watch. Hmmm... maybe the mainspring hasn't fully unwound I thought. Strange.

The next morning, the watch stopped running but the time showed 4 o'clock! Means the watch was actually ticking for 6 hours! I then set it to 10:10 again but this time was careful not to move the watch at all. Again, the watch was ticking after I screwed the crown. This morning, I found the watch showing around the half past 4 mark again! I repeated the exercise and this time watch stopped just before 5 o'clock. Seems like the watch runs for around 6 hours each time.

Before you guys say anything, I didn't wind the watch, it was on the set time position. What do you think happened here? I'm keen to hear if anyone came across this before.

isn’t it a screw down crown? i’m guessing while setting the crown back in the locked position it’s getting wound up enough to run for a few hours
mnl is offline   Reply With Quote
Old 7 November 2020, 08:21 PM   #3
kctt
"TRF" Member
 
kctt's Avatar
 
Join Date: Dec 2010
Location: Melbourne
Watch: AP Diver/SD/GMTIIc
Posts: 228
Quote:
Originally Posted by mnl View Post
isn’t it a screw down crown? i’m guessing while setting the crown back in the locked position it’s getting wound up enough to run for a few hours
When I screw the crown back, I push it to feel the thread before screwing it back on. I'm almost certain at the point where I start the screwing down, the action doesn't wind the watch?
__________________
Rolex Sea Dweller 16600, Rolex GMT Master II 116710LN, Audemars Piguet Royal Oak Offshore Diver, Omega Seamaster Professional, Tudor Pelagos 25600TB, Tudor Black Bay Dark, Zenith Defy Classic

IG: @idighorology
kctt is offline   Reply With Quote
Old 7 November 2020, 10:24 PM   #4
NutNut
"TRF" Member
 
NutNut's Avatar
 
Join Date: Nov 2009
Real Name: Rick
Location: LasIslasFilipinas
Watch: TT GMT IIc
Posts: 826
I agree with @mnl in that the watch winds when you screw the crown back into the lock position. I have a Dual Time with a power meter and noticed that the hand goes up 2 or 3 ticks when locking it. This gives it about 3 or so hours of running time.


Sent from my iPhone using Tapatalk
NutNut is offline   Reply With Quote
Old 8 November 2020, 06:49 AM   #5
dcash0615
2024 Pledge Member
 
dcash0615's Avatar
 
Join Date: Jan 2007
Real Name: Dave
Location: CA
Watch: es
Posts: 4,395
Quote:
Originally Posted by mnl View Post
isn’t it a screw down crown? i’m guessing while setting the crown back in the locked position it’s getting wound up enough to run for a few hours
This
__________________
Instagram @dcash0615

2FA security active
dcash0615 is offline   Reply With Quote
Old 8 November 2020, 01:35 PM   #6
kctt
"TRF" Member
 
kctt's Avatar
 
Join Date: Dec 2010
Location: Melbourne
Watch: AP Diver/SD/GMTIIc
Posts: 228
Quote:
Originally Posted by mnl View Post
isn’t it a screw down crown? i’m guessing while setting the crown back in the locked position it’s getting wound up enough to run for a few hours
Quote:
Originally Posted by NutNut View Post
I agree with @mnl in that the watch winds when you screw the crown back into the lock position. I have a Dual Time with a power meter and noticed that the hand goes up 2 or 3 ticks when locking it. This gives it about 3 or so hours of running time.


Sent from my iPhone using Tapatalk
You are both right. I've repeated the same experiment without setting the time. Just by screwing the crown back on, gives enough juice for the watch to run for 5 hours. Learnt something new today. Cheers fellas.
__________________
Rolex Sea Dweller 16600, Rolex GMT Master II 116710LN, Audemars Piguet Royal Oak Offshore Diver, Omega Seamaster Professional, Tudor Pelagos 25600TB, Tudor Black Bay Dark, Zenith Defy Classic

IG: @idighorology
kctt is offline   Reply With Quote
Old 11 November 2020, 10:52 AM   #7
Burlington
"TRF" Member
 
Burlington's Avatar
 
Join Date: Nov 2017
Location: Europe
Posts: 5,643
Quote:
Originally Posted by kctt View Post
You are both right. I've repeated the same experiment without setting the time. Just by screwing the crown back on, gives enough juice for the watch to run for 5 hours. Learnt something new today. Cheers fellas.

I had indeed noticed the phenomenon - but great to have the duration quantified as I was always curious about that.
__________________
“My tastes are simple; I am easily satisfied with the best.”

― Winston S. Churchill
Burlington is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Wrist Aficionado

My Watch LLC

WatchesOff5th

DavidSW Watches

Takuya Watches

OCWatches


*Banners Of The Month*
This space is provided to horological resources.





Copyright ©2004-2024, The Rolex Forums. All Rights Reserved.

ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

Rolex is a registered trademark of ROLEX USA. The Rolex Forums is not affiliated with ROLEX USA in any way.