ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

mikey · 3 May 2007, 07:05 AM

I had constructed my SS Datejust into a TT Datejust during the Ultimate Transformation post. I decided to go cheap on the band and purchased a top plated TT jubilee. I felt that I still wanted to save some money, so I purchased an italian TT genuine gold and steel jubilee band. I have finally completed my project. I wanted the watch to be true real yellow gold and stainless steel. I have achieved my goal.

PM me for the plated band if interested

diablojota · 3 May 2007, 08:22 AM

Do you still have the original clasp from the original bracelet? If so, you could use that as it would have all the rolex markings...

Rockrolex · 3 May 2007, 08:38 AM

Each to his own, Mikey, but can't say that is something I would do. Putting a TT bracelet on an SS watch just doesn't seem to be the way to go.

But, hey, it's your watch. If you like it, who am I to argue. Enjoy it.

mikey · 3 May 2007, 08:39 AM

I sold my 2 USA Jubilee Bands, so I had to start from scratch. I actually won one on ebay. It should be here next week. I was going to switch out the entire clasp with the Rolex crown and inner markings.

mikey · 3 May 2007, 08:41 AM

Rock, my serial numbers on the case are the only indication of my watch origins of Steel. My watch is 100% TT Datejust. The Rolex clasp is coming next week.

mlb · 3 May 2007, 09:25 AM

Can you tell the difference in Quality between the two? Is the Rolex one heavier and what not . . . ?

Is it that easy to change bracelets?

Looking good

C.J. · 3 May 2007, 10:24 AM

Lookin good, Mikey. You put a lot of work into that watch. I'm glad it makes you smile

mikey · 3 May 2007, 12:14 PM

Thanks for guys for the encouragement! The gold one is heavier than the plated one I was using. The new band will accept the Rolex clasp (modern) D-link. From what I see I have to unroll a main bar by sliding it thru insert the Rolex clasp place the main bar thru and tighten down real tight. The other end is push the bar pin in the adjustment holes and I am done.

ashu2289 · 4 May 2007, 01:19 PM

Good work man

3 May 2007, 07:05 AM	#1
mikey "TRF" Member Join Date: Oct 2006 Location: USA Watch: Oysterdate 6694 Posts: 2,713	Just Arrived I had constructed my SS Datejust into a TT Datejust during the Ultimate Transformation post. I decided to go cheap on the band and purchased a top plated TT jubilee. I felt that I still wanted to save some money, so I purchased an italian TT genuine gold and steel jubilee band. I have finally completed my project. I wanted the watch to be true real yellow gold and stainless steel. I have achieved my goal. PM me for the plated band if interested Attached Images

3 May 2007, 08:22 AM	#2
diablojota "TRF" Member Join Date: Mar 2006 Real Name: Frank Location: Chattanooga, TN Watch: SS Submariner Date Posts: 4,042	Do you still have the original clasp from the original bracelet? If so, you could use that as it would have all the rolex markings... __________________ RTFT - Read The Friggin' Thread FcB

3 May 2007, 08:38 AM	#3
Rockrolex TRF Moderator & 2024 SubLV41 Patron Join Date: May 2005 Real Name: God Location: Washington, D.C. Watch: What do you think? Posts: 37,967	Each to his own, Mikey, but can't say that is something I would do. Putting a TT bracelet on an SS watch just doesn't seem to be the way to go. But, hey, it's your watch. If you like it, who am I to argue. Enjoy it. __________________ Despite the high cost of living, it's still very popular. *Tosser Cabinet Member* Official Member: 'Perpetual 30' Vegas International GTG 2016 Official Member "WIS-CON" Las Vegas International GTG 2017 Official Member "WIS-CON" Las Vegas International GTG 2018 Official Member "WIS-CON" Las Vegas International GTG 2019

3 May 2007, 12:14 PM	#8
mikey "TRF" Member Join Date: Oct 2006 Location: USA Watch: Oysterdate 6694 Posts: 2,713	Thanks for guys for the encouragement! The gold one is heavier than the plated one I was using. The new band will accept the Rolex clasp (modern) D-link. From what I see I have to unroll a main bar by sliding it thru insert the Rolex clasp place the main bar thru and tighten down real tight. The other end is push the bar pin in the adjustment holes and I am done. Attached Images

4 May 2007, 01:19 PM	#9
ashu2289 "TRF" Member Join Date: Apr 2007 Real Name: Ashutosh Location: Rochester NY Watch: Daytonas,SD Posts: 2,342	Good work man __________________ Everything becomes nothing after ROLEX 116520 SS Daytona White Dial 116520 SS Daytona Black Dial 116523 18K&SS Daytona Slate Dial 16600 Sea-Dweller 16710 GMT Master II Pepsi Bezel 16613 18K&SS Submariner Blue Dial 116660 Deepsea Sea-Dweller

3 May 2007, 08:39 AM	#4
mikey "TRF" Member Join Date: Oct 2006 Location: USA Watch: Oysterdate 6694 Posts: 2,713	I sold my 2 USA Jubilee Bands, so I had to start from scratch. I actually won one on ebay. It should be here next week. I was going to switch out the entire clasp with the Rolex crown and inner markings.

3 May 2007, 08:41 AM	#5
mikey "TRF" Member Join Date: Oct 2006 Location: USA Watch: Oysterdate 6694 Posts: 2,713	Rock, my serial numbers on the case are the only indication of my watch origins of Steel. My watch is 100% TT Datejust. The Rolex clasp is coming next week.

3 May 2007, 09:25 AM	#6
mlb Member Join Date: Mar 2007 Real Name: Mike Location: Chicago, Illinois Watch: DJ Posts: 753	Can you tell the difference in Quality between the two? Is the Rolex one heavier and what not . . . ? Is it that easy to change bracelets? Looking good

3 May 2007, 10:24 AM	#7
C.J. "TRF" Member Join Date: Jan 2006 Location: * Posts: 10,196	Lookin good, Mikey. You put a lot of work into that watch. I'm glad it makes you smile

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)