Remove extra links from Rolex??

[hnt1987]

Do you have to take your Rolex to an ARDealer to do it???

I called a couple jewelers but they did not want to do it. I want to know if there is any alternative like removal at home. What ur recommendation???

[TSW]

Get some Loctite and a set of proper screw drivers and do it yourself.

[Hubertus]

Why not doing it at home? You just need the right screw driver, Ref 2100 from the submariner toolkit.

[Tools]

Originally Posted by hnt1987

Do you have to take your Rolex to an ARDealer to do it???

I called a couple jewelers but they did not want to do it. I want to know if there is any alternative like removal at home. What ur recommendation???

Don't call a Jeweler or Jewelry sales outlet.. they likely don't know one end of a watch from another..

Find one that has a watchmaker on staff, or an Authorized Rolex Dealer who can refer you to a qualified watchmaker..

Of course, as mentioned, they are only screws that you can easily take out yourself..

[77T]

If you are not handy, any trusty watchmaker can unscrew a link or two. Otherwise, if you have a steady hand, get a precision 1.4 or 1.6 mm flat head screwdriver and have at it.

[ronbo710]

... I just make sure I have the correct screw driver and I always check the other screws for tightness afterwards. In fact at least once a month I do that. I have had a few loosen on me. But a VERY light dab of loctite will help prevent this too. Good Luck -Ron

[Beelzy]

Meh, if you can figure out the clasp, removing links is a snap.

Simply make sure to obtain a small screwdriver that fits the slot snugly. That is paramount!

[subtona]

are you only removing the screwed in links or do you have a small wrist and need to remove a permanent link?

[mrbill2mrbill2]

Here is the hallow ground screw driver I use.

http://www.ebay.com/itm/ws/eBayISAPI...m=170732585897

[handsfull]

Yep...Hollow ground driver tip....NOT a flat blade, that's what causes link screws (and screwheads) to get mangled/ugly.

[Israguard]

Hi
I just went on e bay and found same seller and what looks like identical item. But!! Only after I ordered did I notice it says "for Panerai". Did I just order wrong item or its same size and its fine. Please see below

Tks

[subtona]

Originally Posted by Israguard

Hi
I just went on e bay and found same seller and what looks like identical item. But!! Only after I ordered did I notice it says "for Panerai". Did I just order wrong item or its same size and its fine. Please see below

TksAttachment 324259

i think the 1.4 is more fitted for rolex.
if your near a home depot pick up a husky mini screwdriver kit, the tips are excellent! about $6 and don't forget to get the loctite.

did i mention, don't forget to get the loctite?

don't muscle the screw, just snug it and then turn it a little more ~1/8 turn.

Husky "8-IN-1 Phillips and Slotted Screwdriver Set"

http://www.homedepot.com/buy/husky-8...l#.UIiUrI4TvpR

good luck


PS i guess you'll have to get a panerai to go with that screwdriver

[hnt1987]

I have the vintage Rolex C&I bracelet that is rarely made for the U.S. only, rarely used on some of the newer Rolex model.

I don't see any screw on it; it looked like it had folded metal or stuff in between. Anyone familiar with Rolex C&I bracelet; picture is posted below. Does this need to be cut???

[Tools]

Early folded Oyster link bracelets require you to actually unfold the link to remove it, then press the folds back in place..

It's nor for the faint-of-heart, and you must be careful to avoid overworking the metal or it will crack..

I'm not sure if the Jubilee is the same, or if it has flat-bars that the link is folded around.. If that is the case, the flat-bars are hammered out the same as bracelets with pins that hold the links together..