ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX
|
8 November 2009, 09:03 AM | #1 |
"TRF" Member
Join Date: Mar 2007
Location: Atlanta, GA
Posts: 115
|
Submariner Scare
I had the shock of my life this morning when I went to put on my blue submariner and it wasn't ticking. I normally keep it on a winder so I thought something was wrong with that. But after an inspection it was still working. So I shook the watch hoping that this would get it started. No dice. So I quickly put the watch down so I wouldn't do anything stupid (and I had somewhere to be).
I had several hours to think about the issue and I had remember reading that when the watch is super used up you sometimes need to wind it to get it going again. So when I get home I get ready to wind it manually when I notice the time and date of the watch. It was the same time that I had left it when I changed it for daylight savings. So now I'm super worried because the watch hasn't been working for close to five days. So it isn't the winder and worse it was probably something I did. So I undo the crown and wind a bit and the watch starts ticking again. I then thought to change the time but I couldn't pull the crown out enough (I was pretty nervous so I might not have been pulling enough). So again I put the watch down before I do something stupid. I come back a bit later and it is still ticking. I undo the crown and pull and it works. So I change the date and the time and wind it a bit more and then put it back in the winder. It's been an hour and everything seems to be working fine. My question is, what could I have done when I changed the time for daylight savings to make the watch stop working? I initially thought that I had tightened the crown too much but that doesn't really make sense. I've relieved that the watch seems to be working but I'm curious as to what would have caused this. Any ideas? Many thanks. Scott |
10 November 2009, 06:52 AM | #2 |
"TRF" Member
Join Date: Mar 2007
Location: Atlanta, GA
Posts: 115
|
Any thoughts at all? Please...
|
10 November 2009, 07:17 AM | #3 |
Banned
Join Date: Jul 2009
Location: fort wayne IN
Watch: Patek 1909003
Posts: 2,176
|
Sounds like to me maybe you had the crown too tight , i could be wrong ...some of the experts should be along shortly....
|
10 November 2009, 07:21 AM | #4 |
2024 SubLV41 Pledge Member
Join Date: Nov 2007
Location: USA
Watch: 126600, 116500LN
Posts: 12,849
|
__________________
"I'm kind of a big deal... on a fairly irrelevant social media site that falsely inflates my fragile ego" |
10 November 2009, 07:25 AM | #5 |
"TRF" Member
Join Date: Oct 2009
Location: .
Posts: 1,343
|
Try asking in the WatchTech sub forum. One of the experts there might be able to answer your question.
__________________
So Mote it be. |
10 November 2009, 08:33 AM | #6 |
"TRF" Member
Join Date: Dec 2007
Real Name: John Eaton
Location: Nome Alaska USA
Watch: Red1680 metres 1st
Posts: 1,869
|
Sounds like your hack stuck when you reset the time.
__________________
Perfection lies not in the organic whole but in the isolated fragment |
10 November 2009, 08:53 AM | #7 |
"TRF" Member
Join Date: Apr 2009
Location: united states
Watch: submariner,daytona
Posts: 707
|
ask jj
|
10 November 2009, 09:02 AM | #8 |
"TRF" Member
Join Date: Sep 2009
Real Name: Dalip
Location: Mumbai and Perth
Watch: Rolex PAM Omega
Posts: 18,656
|
experts will be along...I can only say that my YM did the same thing but I had left the crown pulled out and it didn't get going immediately when I pushed it in and wound it and swirled it.....but it did finally...!!
__________________
------------------------------------------------------------ "The liar's punishment is not in the least that he is not believed, but that he cannot believe anyone else." George Bernard Shaw |
10 November 2009, 09:10 AM | #9 |
"TRF" Member
Join Date: Nov 2008
Location: in my house...
Posts: 5,524
|
I would vigorously move it in swirling motion just to teach it that it doesn't have to stop.. a few slaps and swears.. and if that does not work.. to RSC it goes..
__________________
Cheers, Eduardo Be a WIS not a WUSS... and remove all the stickers.. |
10 November 2009, 09:11 AM | #10 |
Member
Join Date: Oct 2009
Location: Arizona
Posts: 386
|
I start with the simple stuff even though it sounds a little dumb. Did you check to make sure the winder is plugged in and working?
|
10 November 2009, 09:21 AM | #11 |
"TRF" Member
Join Date: Mar 2007
Location: Atlanta, GA
Posts: 115
|
Winder was definitely working.
So is it unusual for the watch to stop if the crown is too tight? Many thanks to all. |
10 November 2009, 09:32 AM | #12 |
Banned
Join Date: Feb 2009
Real Name: Rick
Location: At what TIME?!!!
Watch: the SKY tonite!
Posts: 3,225
|
no
|
10 November 2009, 09:42 AM | #13 |
Member
Join Date: Jul 2009
Real Name: Bill
Location: central Florida
Watch: Sea Dweller
Posts: 97
|
In almost thirty years of using screw-down crown watches from various manufacturers, I have never had one stop because the crown was over-tightened. I can't really see how this could occur ... please share with us how (and why) this might happen. Please.
Cheers! Bill |
10 November 2009, 09:38 AM | #14 |
Member
Join Date: Jul 2009
Location: USA
Watch: 16610
Posts: 366
|
That was strange....very odd situation. I'm glad whatever you did, it worked.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
*Banners
Of The Month*
This space is provided to horological resources.