ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

javier · 4 December 2018, 10:58 PM

I have a problem with a jubilee bracelet. I can not unscrew to remove a link since it is too tight the screw.
Someone knows some technique to do that job ?
Regards, Javier

rambo99 · 4 December 2018, 11:01 PM

try to blow the screw with a hair dryer or put the bracelet under hot water to soften the loctite and try again.

Ian Macdermott · 4 December 2018, 11:05 PM

Also make sure you have a decent correct sized screwdriver.

james.l · 4 December 2018, 11:32 PM

Quote:

Originally Posted by Ian Macdermott

Also make sure you have a decent correct sized screwdriver.

This is key. Also if it's been put together wrong you could have locktite in the barrel of the link rather than the female screw end which will make it even harder.

Sent from my SM-G955F using Tapatalk

jrs146 · 5 December 2018, 12:00 AM

Quote:

Originally Posted by Ian Macdermott

Also make sure you have a decent correct sized screwdriver.

This makes a big difference. Also helps not to scratch the link. That loctite can be a pain in the rear. When in doubt, take to your AD!

Sent from my iPhone using Tapatalk

darkside7 · 5 December 2018, 12:51 AM

Warm water and correct size screw driver

AEC · 5 December 2018, 01:14 AM

Quote:

Originally Posted by darkside7

Warm water and correct size screw driver

This. I soak just the bracelet in hot water for five minutes (I avoid soaking the watch in very hot water if possible, but I'm overly cautious that way). Using the correctly sized screwdriver, the screw will come out very easily.

Boaters · 5 December 2018, 02:02 AM

I put a cup of water in the microwave for a minute then soak the problem for a couple of minutes, make sure you have the proper screwdriver and it should come loose if not repeat the process.

Alcan · 5 December 2018, 02:25 AM

Make sure you are using the correct size hollow ground screwdriver, precision ground is preferred, not a standard taper.

Tools · 5 December 2018, 05:57 AM

If it has been put together with loc-tite, heat is the breaker for this product.

You need to apply heat to the threads (opposite the slot) to break the seal and the screw should easily unscrew.

NoVaSubowner · 5 December 2018, 06:00 AM

Quote:

Originally Posted by javier

I have a problem with a jubilee bracelet. I can not unscrew to remove a link since it is too tight the screw.
Someone knows some technique to do that job ?
Regards, Javier

The Imperial Empire will not tolerate Rebel links of any type and will move to crush all outposts of resistance.

Fencer · 5 December 2018, 06:01 AM

The type of thread locker used there is very gentle one, I have never had to use heat, just good quality screwdriver, usually 1.5mm Wiha model, made in Germany. They are readily available, for instance from McMaster Carr.

RJRJRJ · 5 December 2018, 06:07 AM

I've never had to use heat (yet?). If it doesn't budge, I tighten it more and then try to unscrew again. It sounds counterintuitive, but it's worked for me.

And of course, use the proper screwdriver or you're just going to mess up the screw.

ROLMARINER · 5 December 2018, 06:25 AM

If all the good advice fails, you can always go with the Rule Of Two which states:

Take 2 links from the side that is stuck (1 good, 1 stuck) and trade those 2 for two links on the other side (2 good). This will then move the problem pair with the stuck screw to the other side of the bracelet and allow you to remove the 1 link from the side you intended to in the first place.

Beckster · 6 December 2018, 01:07 AM

Quote:

Originally Posted by ROLMARINER

If all the good advice fails, you can always go with the Rule Of Two which states:

Take 2 links from the side that is stuck (1 good, 1 stuck) and trade those 2 for two links on the other side (2 good). This will then move the problem pair with the stuck screw to the other side of the bracelet and allow you to remove the 1 link from the side you intended to in the first place.

Very good idea. Might come in handy some day. Thanks!

ROLMARINER · 6 December 2018, 01:39 AM

Quote:

Originally Posted by Beckster

Very good idea. Might come in handy some day. Thanks!

Happy to contribute! I've learned so much from this forum its nice to give back.

I ran into this problem when I took delivery of my BLRO which was imbalanced and needed one link to move from the 12:00 side to the 6:00 side to fit properly. The one link I needed to shift was stuck and it dawned on me that I could remove 2 links, move both over, and swap for 1 link moving the other way. The end result was the same and the stuck jubilee link (which is still stuck) became a non-issue.

4 December 2018, 10:58 PM	#1
javier "TRF" Member Join Date: Aug 2016 Location: Argentina Posts: 804	Do you know how to unscrew a rebel link ? I have a problem with a jubilee bracelet. I can not unscrew to remove a link since it is too tight the screw. Someone knows some technique to do that job ? Regards, Javier

4 December 2018, 11:05 PM	#3
Ian Macdermott "TRF" Member Join Date: May 2015 Real Name: Willy.B.Banned Location: Sheol Watch: ing the detectives Posts: 2,721	Also make sure you have a decent correct sized screwdriver. __________________ Welax no one other than wobblers muggers and sad WIS types notices your Wolex. The rest of the populace are way too busy staring at their shiny new iPhone 24s or worrying about paying the gas bill..

5 December 2018, 12:51 AM	#6
darkside7 "TRF" Member Join Date: Dec 2006 Real Name: Eddie Location: Austin Tx Watch: Sub-C Posts: 510	Warm water and correct size screw driver __________________

5 December 2018, 02:25 AM	#9
Alcan 2024 Pledge Member Join Date: Nov 2006 Real Name: Al Location: Way Up North Watch: your P's & Q's Posts: 10,473	Make sure you are using the correct size hollow ground screwdriver, precision ground is preferred, not a standard taper. Attached Images __________________ Member #1,315 I don't want to get technical, but according to chemistry alcohol IS a solution!

5 December 2018, 05:57 AM	#10
Tools TRF Moderator & 2024 SubLV41 Patron Join Date: May 2007 Real Name: Larry Location: Mojave Desert Watch: GMT's Posts: 43,514	If it has been put together with loc-tite, heat is the breaker for this product. You need to apply heat to the threads (opposite the slot) to break the seal and the screw should easily unscrew. __________________ (Chill ... It's just a watch Forum.....) NAWCC Member

4 December 2018, 11:01 PM	#2
rambo99 Banned Join Date: Aug 2018 Location: Tokyo Watch: SD43,PAM1616,Hulk Posts: 3,567	try to blow the screw with a hair dryer or put the bracelet under hot water to soften the loctite and try again.

5 December 2018, 02:02 AM	#8
Boaters 2024 Pledge Member Join Date: May 2015 Real Name: Mike Location: Pacific Northwest Watch: 116610LV 16710 SD Posts: 10,653	I put a cup of water in the microwave for a minute then soak the problem for a couple of minutes, make sure you have the proper screwdriver and it should come loose if not repeat the process.

5 December 2018, 06:01 AM	#12
Fencer "TRF" Member Join Date: Nov 2018 Location: usa Posts: 287	The type of thread locker used there is very gentle one, I have never had to use heat, just good quality screwdriver, usually 1.5mm Wiha model, made in Germany. They are readily available, for instance from McMaster Carr.

5 December 2018, 06:07 AM	#13
RJRJRJ "TRF" Member Join Date: Aug 2011 Location: USA Posts: 3,495	I've never had to use heat (yet?). If it doesn't budge, I tighten it more and then try to unscrew again. It sounds counterintuitive, but it's worked for me. And of course, use the proper screwdriver or you're just going to mess up the screw.

5 December 2018, 06:25 AM	#14
ROLMARINER Banned Join Date: Jun 2018 Location: Long Island Watch: 500C, BLRO Posts: 300	If all the good advice fails, you can always go with the Rule Of Two which states: Take 2 links from the side that is stuck (1 good, 1 stuck) and trade those 2 for two links on the other side (2 good). This will then move the problem pair with the stuck screw to the other side of the bracelet and allow you to remove the 1 link from the side you intended to in the first place.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)