ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

DaveN · 21 July 2007, 08:38 AM

I'm planning on a GMT II but will most likely get it from an out of town source. Woody posted on another thread about removing links from one side and adding to the other to get the fit perfected.

Is there a trick to band sizing? Does it have to be performed at a dealer or might it be a DIY project? If I supply my wrist measurement can the seller size it for me? I will probably have to get the watch by mail since I want to beat the price increase and won't be traveling soon.

Dave

USMCsilver · 21 July 2007, 09:14 AM

I've got one, and while I am far from being an expert, all ya need is a teeny, tiny flathead screwdriver and you'll be set.

Tools · 21 July 2007, 09:58 AM

Dave,

I think that bracelet adjustment on a new GMT would be way to difficult.

I have lot's of experience with screws and screwdrivers and such....so...send it to me....I will make sure it fits my wrist nicely..

heck, I'll even pay shipping... one way...

Once done, I will provide you with plenty of pictures of the nice fit for you to enjoy at your liesure......

DaveN · 21 July 2007, 11:55 AM

Larry,
Your offer is too kind. I would feel bad if I didn't cover shipping.... ;)

JJ Irani · 21 July 2007, 01:21 PM

Quote:

Originally Posted by DaveN

I'm planning on a GMT II but will most likely get it from an out of town source. Woody posted on another thread about removing links from one side and adding to the other to get the fit perfected.

Is there a trick to band sizing? Does it have to be performed at a dealer or might it be a DIY project? If I supply my wrist measurement can the seller size it for me? I will probably have to get the watch by mail since I want to beat the price increase and won't be traveling soon.

Dave

Hi Dave,

It's very simple.

For some unknown reason, Rolex ship the Oysterlock bracelet (found on the GMT-II and Exp-II) with a 7+6 arrangement, i.e. 7 links on the '12' side and 6 links on the '6' side.

All you have to do is take off one link from the '6' side and add it to the '12' side....so your new arrangement becomes 8+5 - like this!! And your clasp will be perfectly centralised. See pics below.

Cheers - JJ

DaveN · 21 July 2007, 01:31 PM

JJ,
Great photos as always. With all the links what is the circumference of the watch? How much does removing a large or small link change that number?

Dave

JJ Irani · 21 July 2007, 01:36 PM

Quote:

Originally Posted by DaveN

JJ,
Great photos as always. With all the links what is the circumference of the watch? How much does removing a large or small link change that number?

Dave

Well, I have a 7¼" left wrist and I don't need to take off any links at all - just the transfer of one link from the '6' side to the '12' side as described above....and then my fit is like this!!

JJ Irani · 21 July 2007, 01:37 PM

Dave,

If you do need to take off ONE link, then do so from the '6' side....so that your final arrangement is 7 + 5.

JJ

DaveN · 21 July 2007, 01:43 PM

JJ,
I measured and my wrist is also 7 1/4". I'm headed back to the AD the first of next week and I'll check which pin on the clasp the watch is set at. I'm assuming that unlike yours which has a pin in the number 2 position their must be in the number 5. That would add quite a bit to the band. Again, a picture is worth....

Dave

JJ Irani · 21 July 2007, 01:45 PM

Quote:

Originally Posted by DaveN

JJ,
I measured and my wrist is also 7 1/4". I'm headed back to the AD the first of next week and I'll check which pin on the clasp the watch is set at. I'm assuming that unlike yours which has a pin in the number 2 position their must be in the number 5. That would add quite a bit to the band. Again, a picture is worth....

Dave

My pin is NOT actually in the No.2 position....it's in the 4th hole from the end of the clasp.

There's another hole concealed under the flipover secure clasp.

JJ

DaveN · 21 July 2007, 01:46 PM

Is there a tool for easily pushing in the clasp adjustment pins without scratching the watch?

JJ Irani · 21 July 2007, 01:48 PM

Quote:

Originally Posted by DaveN

Is there a tool for easily pushing in the clasp adjustment pins without scratching the watch?

Yes....I have this SD screwdriver which is an absolute must in any Rolex watch collector's toolkit.

JJ

Bama · 21 July 2007, 02:09 PM

JJ, Where did you buy that SD screwdriver? Did you purchase it by itself or did it come with a SD that you used to own? I really need something like that. I'm scared to do any adjustments for fear of scratching the clasp.

JJ Irani · 21 July 2007, 04:53 PM

Quote:

Originally Posted by Bama

JJ, Where did you buy that SD screwdriver? Did you purchase it by itself or did it come with a SD that you used to own? I really need something like that. I'm scared to do any adjustments for fear of scratching the clasp.

That SD screwdriver was given to me by a friend several years ago. He happened to have a spare one and let me have it.

I think they are available on ebay, but any good screwdriver will do the trick. Just place a small piece of cellotape over the screw-head, then push the screwdriver through the tape and turn. That way, if the screwdriver slips, you will not scratch the side of the bracelet.

Cheers - JJ

Bama · 22 July 2007, 12:52 PM

Quote:

Originally Posted by JJ Irani

That SD screwdriver was given to me by a friend several years ago. He happened to have a spare one and let me have it.

I think they are available on ebay, but any good screwdriver will do the trick. Just place a small piece of cellotape over the screw-head, then push the screwdriver through the tape and turn. That way, if the screwdriver slips, you will not scratch the side of the bracelet.

Cheers - JJ

Thanks JJ

S2000 Driver · 22 July 2007, 11:31 AM

Quote:

Originally Posted by JJ Irani

Yes....I have this SD screwdriver which is an absolute must in any Rolex watch collector's toolkit.

JJ

Just ordered one of these for myself!

jaycee · 22 July 2007, 11:14 AM

Quote:

Originally Posted by DaveN

Is there a tool for easily pushing in the clasp adjustment pins without scratching the watch?

A toothpick works quite nicely. I only discovered this after slightly scratching my clasp.

chemist · 21 July 2007, 03:18 PM

Honestly, all you need is some cheap eyeglass screwdrivers. Whether it will scratch is depend on how careful you do it. When I first bought my Plat DD, my AD made a little dent on the screw itself when she adjusted the bracelet for me. I added one link back few days ago because it is uncomfortable to wear too tight in the summer time. I used the cheap screwdriver and did a perfect job.

DaveN · 22 July 2007, 12:31 PM

Where did you order it from?

21 July 2007, 08:38 AM	#1
DaveN "TRF" Member Join Date: Jun 2007 Location: NC Watch: GMT II TT 116713 Posts: 133	New GMT II Bracelet, how difficult is adjustment? I'm planning on a GMT II but will most likely get it from an out of town source. Woody posted on another thread about removing links from one side and adding to the other to get the fit perfected. Is there a trick to band sizing? Does it have to be performed at a dealer or might it be a DIY project? If I supply my wrist measurement can the seller size it for me? I will probably have to get the watch by mail since I want to beat the price increase and won't be traveling soon. Dave

21 July 2007, 09:14 AM	#2
USMCsilver "TRF" Member Join Date: Jul 2007 Real Name: Sterling Location: Middle of SC Watch: Anniv. GMT II Posts: 908	I've got one, and while I am far from being an expert, all ya need is a teeny, tiny flathead screwdriver and you'll be set. __________________ The Original USMCsilver© ~~><~~

21 July 2007, 01:37 PM	#8
JJ Irani Fondly Remembered Join Date: May 2005 Real Name: JJ Location: Auckland, NZ Watch: ALL SOLD!! Posts: 74,319	Dave, If you do need to take off ONE link, then do so from the '6' side....so that your final arrangement is 7 + 5. JJ __________________ Words fail me in expressing my utmost thanks to ALL of you for this wonderful support during my hour of need!! I firmly believe that my time on planet earth is NOT yet up!! I shall fight this to the very end.......and WIN!!

21 July 2007, 09:58 AM	#3
Tools TRF Moderator & 2024 SubLV41 Patron Join Date: May 2007 Real Name: Larry Location: Mojave Desert Watch: GMT's Posts: 43,514	Dave, I think that bracelet adjustment on a new GMT would be way to difficult. I have lot's of experience with screws and screwdrivers and such....so...send it to me....I will make sure it fits my wrist nicely.. heck, I'll even pay shipping... one way... Once done, I will provide you with plenty of pictures of the nice fit for you to enjoy at your liesure......

21 July 2007, 11:55 AM	#4
DaveN "TRF" Member Join Date: Jun 2007 Location: NC Watch: GMT II TT 116713 Posts: 133	Larry, Your offer is too kind. I would feel bad if I didn't cover shipping.... ;)

21 July 2007, 01:31 PM	#6
DaveN "TRF" Member Join Date: Jun 2007 Location: NC Watch: GMT II TT 116713 Posts: 133	JJ, Great photos as always. With all the links what is the circumference of the watch? How much does removing a large or small link change that number? Dave

21 July 2007, 01:43 PM	#9
DaveN "TRF" Member Join Date: Jun 2007 Location: NC Watch: GMT II TT 116713 Posts: 133	JJ, I measured and my wrist is also 7 1/4". I'm headed back to the AD the first of next week and I'll check which pin on the clasp the watch is set at. I'm assuming that unlike yours which has a pin in the number 2 position their must be in the number 5. That would add quite a bit to the band. Again, a picture is worth.... Dave

21 July 2007, 01:46 PM	#11
DaveN "TRF" Member Join Date: Jun 2007 Location: NC Watch: GMT II TT 116713 Posts: 133	Is there a tool for easily pushing in the clasp adjustment pins without scratching the watch?

21 July 2007, 02:09 PM	#13
Bama "TRF" Member Join Date: Jun 2007 Real Name: John Location: Washington, DC Posts: 1,150	JJ, Where did you buy that SD screwdriver? Did you purchase it by itself or did it come with a SD that you used to own? I really need something like that. I'm scared to do any adjustments for fear of scratching the clasp.

21 July 2007, 03:18 PM	#18
chemist Member Join Date: Mar 2007 Location: usa Posts: 77	Honestly, all you need is some cheap eyeglass screwdrivers. Whether it will scratch is depend on how careful you do it. When I first bought my Plat DD, my AD made a little dent on the screw itself when she adjusted the bracelet for me. I added one link back few days ago because it is uncomfortable to wear too tight in the summer time. I used the cheap screwdriver and did a perfect job.

22 July 2007, 12:31 PM	#19
DaveN "TRF" Member Join Date: Jun 2007 Location: NC Watch: GMT II TT 116713 Posts: 133	Where did you order it from?

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)